PLCW-600 SERIES2 1/2” X 6”

    PRODUCT: PLCW-600 AS MANUFACTURED BY PRL GLASS SYSTEMS, INC.
    CW-600 - V1
    CW-600 - V3 (1)
    CW-600 - V2
    • Manufacturer Qualifications: Minimum 5 year experience manufacturing similar products.
    • Installer Qualifications: Minimum 2 year experience installing similar products.
    • Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship.
    • Finish areas designated by Architect.
    • Do not proceed with remaining work until workmanship is approved by Architect.
    • Refinish mock-up area as required to produce acceptable work.

    READ MORE

     

    • Material: Frames, assembly clips, trims and miscellaneous extrusions shall be extruded from Aluminum 6063-T6 alloy.
    • Glazing Gaskets:
    • Class II color anodized aluminum shall:
      1. Color: Champagne.
      2. Color: Light
      3. Color: Medium
      4. Color: Dark
      5. Color: Black
    • Structural silicone compatible gasket: true silicone gasket -70 Durometer Shore "A", complying with ASTM C1115, Type C.
    • Thermal isolators: extruded rigid Geon complying with AAMA-303 and ASTM-D-1784-9.
    • End Dams: Pre-molded end dams made from closed cell EPDM (Ethylene Propylene Diene Monomer) sponge to ASTM C509.
    READ MORE

    Learn more information about our contfiguration Max Cabo Bipass System

    by clicking here.

    1.1 REFERENCES
    A. American Architectural Manufacturers Association (AAMA):
      1. 1. AAMA/NWWDA 101/I.S. 2-97 – Voluntary Specification, Performance Requirements and Test Procedures for Air Leakage Resistance, Water Penetration Resistance, Structural Loading, Forced Entry Resistance.
      1. 2. AAMA-501.1 – Standard Test Method for Water Penetration of Windows, Curtain Walls and Doors Using Dynamic Pressure.
      1. 3. AAMA 501.4 – Recommended Static Test Method for Evaluating Curtain Wall and Storefront Systems Subjected to Seismic and Wind Induced Interstory Drifts.
      1. 4. AAMA 2605 – Voluntary Specification, Performance Requirements and Test Procedures for Superior Performing Organic Coatings on Aluminum Extrusions and Panels.
    B. ASTM International (ASTM):
      1. 1. ASTM B 221 – Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes.
      1. 2. ASTM E 283 – Test Method for Determining the Rate of Air Leakage Through Exterior Windows, Curtain Walls, and Doors under Specified Pressure Differences across the Specimen.
      1. 3. ASTM E330 – Standard Test Method for Structural Performance of Exterior Windows, Doors, Skylights and Curtain Walls by Uniform Static Air Pressure Difference.
      1. 4. ASTM E 331 – Test Method for Water Penetration of Exterior Windows, Curtain Walls, and Doors by Uniform Static Air Pressure Difference.
    1.  
    VIEW PDF
    PROJECT NAME = cw601 PROJECT NUMBER=1

    1. Ixx – NEUTRAL MOMENT OF INERTIA = 4.80288 AREA = 1.64775
      Iyy – NEUTRAL MOMENT OF INERTIA = 1.42838 PERIMETER = 17.7867
      Ixy – NEUTRAL MOMENT OF INERTIA = .000000
      Ip – POLAR MOMENT OF INERTIA = 6.23127
      Imax – MAXIMUM MOMENT OF INERTIA = 4.80288
      Imin – MINIMUM MOMENT OF INERTIA = 1.42838
      Theta – PRINCIPLE TO LOCAL ANGLE = .000000
      Rmax – MAXIMUM RADIUS OF GYRATION= 1.70728
      Rmin – MINIMUM RADIUS OF GYRATION= .931056

    VIEW PDF
    1.  

    materials and finishes

    Glass Thickness Color:

    • Color: Clear
    • Color: Starphire
    • Color: Texture
    • Color: Grey
    • Color: Bronze
    • Color: Laminated

    Avilable finishes aluminum shall conform:

    • Color: Clear Anodize
    • Color: Bronze Anodize
    • Color: Mill Finish
    1. Air infiltration: Limit air leakage through fixed glazing and frames to 026 cfm/ft2/min (0.01 L/s/m2) when tested in accordance with ASTM E-283-04 at a cross pressure of 6.24 psf (0.30 kPa).
    2. Water Penetration under Static Pressure: System shall not evidence uncontrolled water penetration at a cross pressure of 15 psf (103 kPa) when tested in accordance with ASTM-E331-00.
    3. Water Penetration under Dynamic Pressure: System shall not evidence uncontrolled water penetration at a cross pressure of 15 psf (103 kPa) when tested in accordance with AAMA-501.1-05.

    EXPLORE ALL THE PRODUCTS

    view all

    Love The Results

    Point-supported Curtain Wall, Double-skin Curtain Wall, Transparent Facade System, Sustainable Curtain Wall, Curtain Wall Manufacturer
    Point-supported Curtain Wall, Double-skin Curtain Wall, Transparent Facade System, Sustainable Curtain Wall, Curtain Wall Manufacturer
    Point-supported Curtain Wall, Double-skin Curtain Wall, Transparent Facade System, Sustainable Curtain Wall, Curtain Wall Manufacturer
    Point-supported Curtain Wall, Double-skin Curtain Wall, Transparent Facade System, Sustainable Curtain Wall, Curtain Wall Manufacturer
    Point-supported Curtain Wall, Double-skin Curtain Wall, Transparent Facade System, Sustainable Curtain Wall, Curtain Wall Manufacturer

    Discover our entire product gallery by clicking here

    PRL Glass  Systems Inc
    13644 Nelson Ave, Industry, CA. 91746
    251 Mason Way, Industry, CA. 91746

    PRL Aluminum Inc
    14760 Don Julian rd, Industry, Ca. 91746

    Quick Links
    Oppening Hours
    Newsletter
    Click here